# Kismet drone config file

version=Feb.04.01a

# Name of server (Purely for organiational purposes)
servername=Kismet

# User to setid to (should be your normal user)
suiduser=your_user_here

# Port to serve packet data... This probably shouldn't be the same as the port
# you configured kismet_server for, or else you'll have problems running them 
# on the same system.
tcpport=3501
# People allowed to connect, comma seperated IP addresses or network/mask
# blocks.  Netmasks can be expressed as dotted quad (/255.255.255.0) or as
# numbers (/24)
allowedhosts=127.0.0.1
# Address to bind to.  Should be an address already configured already on 
# this host, reverts to INADDR_ANY if specified incorrectly.
bindaddress=127.0.0.1
# Maximum number of concurrent stream attachments
maxclients=5

# Sources are defined as:
# source=sourcetype,interface,name[,initialchannel]
# Source types and required drivers are listed in the README.
# The initial channel is optional, if hopping is not enabled it can be used
# to set the channel the interface listens on.
# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE
source=none,none,addme

# Comma-separated list of sources to enable.  This is only needed if you wish 
# to selectively enable multiple sources.
# enablesources=prism,cisco

# Do we channelhop?
channelhop=true

# How many channels per second do we hop?  (1-10)
channelvelocity=5

# By setting the dwell time for channel hopping we override the channelvelocity
# setting above and dwell on each channel for the given number of seconds.
#channeldwell=10

# Do we split channels between cards on the same spectrum?  This means if 
# multiple 802.11b capture sources are defined, they will be offset to cover
# the most possible spectrum at a given time.  This also controls splitting
# fine-tuned sourcechannels lines which cover multiple interfaces (see below)
splitchannels=true

# Basic channel hopping control:
# These define the channels the cards hop through for various frequency ranges
# supported by Kismet.   More finegrain control is available via the 
# "sourcechannels" configuration option.
# 
# Don't change the IEEE80211<x> identifiers or channel hopping won't work.

# Users outside the US might want to use this list:
# defaultchannels=IEEE80211b:1,7,13,2,8,3,14,9,4,10,5,11,6,12
defaultchannels=IEEE80211b:1,6,11,2,7,3,8,4,9,5,10

# 802.11g uses the same channels as 802.11b...
defaultchannels=IEEE80211g:1,6,11,2,7,3,8,4,9,5,10

# 802.11a channels are non-overlapping so sequential is fine.  You may want to
# adjust the list depending on the channels your card actually supports.
# defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64,100,104,108,112,116,120,124,128,132,136,140,149,153,157,161,184,188,192,196,200,204,208,212,216 
defaultchannels=IEEE80211a:36,40,44,48,52,56,60,64

# Combo cards like Atheros use both 'a' and 'b/g' channels.  Of course, you
# can also explicitly override a given source.  You can use the script 
# extras/listchan.pl to extract all the channels your card supports.
defaultchannels=IEEE80211ab:1,6,11,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64

# Fine-tuning channel hopping control:
# The sourcechannels option can be used to set the channel hopping for 
# specific interfaces, and to control what interfaces share a list of 
# channels for split hopping.  This can also be used to easily lock
# one card on a single channel while hopping with other cards.
# Any card without a sourcechannel definition will use the standard hopping
# list.
# sourcechannels=sourcename[,sourcename]:ch1,ch2,ch3,...chN

# ie, for us channels on the source 'prism2source' (same as normal channel
# hopping behavior):
# sourcechannels=prism2source:1,6,11,2,7,3,8,4,9,5,10

# Given two capture sources, "prism2a" and "prism2b", we want prism2a to stay
# on channel 6 and prism2b to hop normally.  By not setting a sourcechannels 
# line for prism2b, it will use the standard hopping.
# sourcechannels=prism2a:6

# To assign the same custom hop channel to multiple sources, or to split the 
# same custom hop channel over two sources (if splitchannels is true), list
# them all on the same sourcechannels line:
# sourcechannels=prism2a,prism2b,prism2c:1,6,11

